To replace or clean an agitator, you will need to remove it from the washing machine, and the method will vary between different washer models.Īlways make sure to refer to the user manual of your washer model for proper instructions. Over time, these components may need a thorough cleaning due to residual build-ups of dirt and detergent or a replacement in the event of wear-outs. Final ThoughtsĪgitators are found in top-load washing machine models however, most modern-day top-loaders these days use a disk-like impeller. Then, loosen the screws and use a knife or a screwdriver to carefully lift the agitator out of the machine. Next, take the cap out to locate the screws holding the agitator in place. In order to remove the agitator from the Maytag Centennial washing machine, locate the cap at the bottom of the washtub. How to remove the agitator from a Maytag Centennial washing machine? Just make sure to get a proper replacement by searching for the model number of your washer. So if your agitator is broken or damaged, you can follow the same process. Note: The above steps are applicable for replacing a new agitator as well. Reconnect the dispenser to the top, if applicable, and make sure to fix it firmly.įinally, turn on the water supply and plug in the machine to check if everything works fine. Make sure to place the bolt properly in its place, and then tighten it using the socket. ![]() Step 6: Reinstall the agitatorįinally, to put the agitator back in, just reverse the process you used to remove it.įirst, twist the agitator into its place, then push it down until it’s snug, and then bolt it back again. Just remember to rinse well and dry completely before replacing the agitator in its place. Removing the agitator will allow access to previously inaccessible areas of the tub, allowing you to do a thorough cleaning. Now, it is time to clean the agitator thoroughly with soapy water (if you intended to clean the agitator). Make sure to first clean the area where the agitator was sitting with soapy water and a sponge. Step 5: Clean the area where the agitator sits Place an old towel in the bottom of a bucket to cushion the agitator, and then carefully lift it out of the drum. Once the nut is loosened, use a pair of pliers to gently wiggle the agitator back and forth until it comes loose from the shaft. Use a socket wrench set to loosen the nut that holds the agitator in place. Once the fabric softener compartment is removed, you will now be able to see a bolt under it that holds the agitator to the shaft. In some models, you will have to hold the agitator from the bottom and then twist the dispenser counterclockwise to separate them. To remove the dispenser, simply hold the top compartment of the agitator to pull it out and separate it. Most agitators include a fabric softener dispenser at the top, so you will need to remove it first if your model has one. You will now see a long, spindle-like agitator placed right in the center of the washtub. Now, lift the door of your top-load washer and make sure it is empty and does not have any clothes inside. This can be done by unplugging it from the electrical outlet or turning off the circuit breaker that powers it.Īlso, disconnect the water supplies to ensure that water isn’t flowing while the machine is not in use. Here’s the step-by-step guide to removing the agitator Step 1: Unplug the washerīefore you begin any repair, it’s important to turn off the power to your washing machine. Removing the agitator from your Maytag washer may look difficult initially, but if you look at the steps below, it’s not that difficult. How to remove the agitator from Maytag washer? Components such as the wash drum or the motor or its bearing, etc. Another possibility could be that you want to work on the connected components.It may happen that the agitator is broken and needs a replacement.There needs to be a thorough cleaning of the agitator, but that may be difficult if it is still attached to its place.Removing an agitator from the washing machine is done for several reasons. In most cases, you will need to remove the fabric softener dispenser first, then unbolt the screws holding the agitator to detach it from the drum.You can do so by using the model number of your washer. If you are planning to replace the agitator it’s important that you find a proper replacement.Refer to the user manual to confirm if yours has a detachable agitator or not. Some washer models have a non-detachable agitator (so you may not be able to detach them).Agitators are usually found in top-load models.Agitators can be removed yourself using the basic hardware tools, but remember, not all washers have the same method to remove them.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |